I gave you all the karma I could in the comments. So, it is important to allow Plex central servers to reach your server and therefore to know what country are hosting them to allow those countries in your firewall.Įvery person giving you a bad karma does not seem to know about this specific Plex behavior. If it is, then the client will be redirected to your Plex server's IP for a direct connection.īut before getting the client to the server, "Plex central services" are checking if your server (the one attached to your Plex account and being requested by the client) is reachable as I said, and if their servers cannot reach your Plex server, it will start a tunnelled session, just like when the ports are closed. They are right when they say the client IP is the one to allow for direct connection.īUT, unless you access the Plex server with its IP address directly, any Plex app or the URL will make Plex's central servers first check if your Plex server has its ports opened and is reachable. Hi OP, it's amazing how no one understood your problem and gave you so much negative karma. This is a bad idea, security wise, and completely unnecessary. Steps 2,3, & 4 promote the use of UPnP/NATPMP. I realize that the publicly exposed port is visible within the networks allowed in the firewall rule but logging is enabled for that rule so there is an audit trail if I ever need it.Ī word of caution: One commenter posted the article on remote access. None of my remote clients use the Plex mobile app so I only had to find the network IP range for my and my wife's mobile phones and add that to the firewall rule. Assuming their IPs might change, I made a firewall rule for each network range for the WAN forwarded port and applied the rule to incoming traffic on my router's WAN port. But, then I took each of their IPs and looked them up on so that I could see the network range/CIDR block/etc. Then I got each client to send me their IP address (of their home) using. For IP forwarding, I changed the TCP port to: 32xxx on the WAN side (on the Plex server config). I just read through all the comments and they are pretty much spot on. Please go to the relevant subreddits and support forums, for example: Build help and build shares posts go in their respective megathreads No referral / affiliate links, personal voting / campaigning / funding, or selling posts Welcome to /r/Plex, a subreddit dedicated to Plex, the media server/client solution for enjoying your media! Plex Community Discord Rules If everything went well you should be able to access PLEX remotely, if not, I have no idea what the problem is.Latest Regular Threads: No Stupid Q&A: Tool Tuesday: Build Help: Share Your Build: Submit Troubleshooting Post Files not showing up correctly? Port Forwarding did not work but again, it was. Then with the help of this YouTube video Plex How to Port Forward I looked into Port Forwarding Plex on my router. Install both miniupnpd and luci-app-upnp. After reading this Plex support page Plex Troubleshooting Remote Access I used whatismyip to determine whether I had a Double NAT mucking it up. We’ll also want to install and enable UPnP. In this example my PLEX server has an internal IP of 10.10.10.100. Plex informed some users this week that it will no longer allow users to run servers at a hosting provider where lots of TOS violations occur. The IP should be the IP address of your PLEX server. You’ll need to add each of the following ports. I prefer using OpenWRT, due to the high level of configurability. In this example my Buffalo router has a LAN IP of 192.168.1.151. The IP should be the IP address of the router which the PLEX server connects to. click Yes to the "are you sure" message.Verizon Router Configuration Port Forwarding I use the FIOS AC1750 router from which I run an ethernet connection to a Buffalo WZR-HP-AG300H running OpenWRT to which I have my PLEX server and other internet devices connected. With this provider, you can easily unblock geo-restricted Plex content and many other streaming sites. In my network I am using a Double-NAT setup with FIOS. You can watch and access Plex remotely by using one of its 600+ US servers, which will give you access to live TV channels, streaming add-ons, and on-demand shows and films. In the PLEX Troubleshooting Remote Access they have a small section on setting up for Double-NAT, but don’t really get into how to actually do it.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |